Fragile roofs: the checks that stop roofing’s most common fatal fall
By Simon Winson
Most fatal roof falls are through fragile materials, not off the edge. I see it in paperwork and on site. Here’s how I survey, plan and control fragile roof risks so you do not go through an old rooflight or fibre cement sheet on a wet Tuesday.
A fragile roof is any surface that will not safely take a person’s weight, like fibre cement sheets, old rooflights and corroded metal sheets. To stop the classic fatal fall through, assume fragility until proven otherwise, survey from below, then control with covers, staging, nets below, barriers and clear signage. These are the controls set out in HSG33 Health and safety in roof work, and required by the Work at Height Regulations 2005 when work near fragile surfaces cannot be avoided. HSE’s fatal injury statistics show falls from height remain the leading cause of construction fatalities, with many through fragile materials.
The reality of fragile roofs and why people die
I review roofing RAMS every week and the same pattern jumps out. People fall through, not off. A tidy scaffold and nice handrails do nothing for a knackered fibre cement sheet or a brittle GRP rooflight hidden under algae. HSE’s fatal injury statistics say falls from height are still the top killer in construction, and a good chunk of the roofing deaths are through fragile materials. Most of these would not have happened with basic covers and staging, set out in HSG33 Health and safety in roof work.
Fragile roof is not a fancy term. It just means a surface that will not take a person’s weight or a load, even if it looks fine from the yard. Think a 1970s farm unit on a wet Tuesday, sheets sweating, gutters full of green slime. Your boot slips, your knee goes through a skylight you did not spot, then your whole weight follows it. I have stood under those roofs and seen daylight where there should not be any.
The law is clear. The Work at Height Regulations 2005 require you to avoid working on or near fragile surfaces where reasonably practicable, and to provide platforms, coverings, guard rails or similar protection, with prominent warning signs if you cannot avoid the risk. HSG33 gives the industry method for doing that on different roof types. When I reject RAMS, it is usually because they list edge protection and harnesses, then say nothing about the fragile surface under their feet.
For the paperwork and the thinking behind it, this roofing risk assessment guide shows what to write up and why fragile surfaces need specific controls.
What counts as a fragile roof on real jobs
If you remember only one thing, make it this. Fibre cement sheets, old rooflights and corroded metal are fragile until proven otherwise. I treat every asbestos cement roof as fragile on first visit, and most non-asbestos fibre cement too, especially if it looks chalky or has hairline cracks. I have seen sheets that looked sound from above but were paper-thin over a purlin when you checked from below.
Rooflights are the killer. GRP and PVC rooflights go brittle with age and UV. The ones hidden under moss or painted over are worse because people forget they are there. I have seen rooflights that flex under a hand, never mind a boot. HSG33 is blunt on this point, treat all rooflights as fragile unless you have clear evidence they are non-fragile and suitably protected.
Watch for corrosion at fixings and end laps on metal sheeting. The sheet can feel firm between purlins but will tear at a rusted fixing hole like wet cardboard if you load it wrong. Timber decks can be fragile too when rot creeps in around rooflights or outlets. And there are one-offs, like fragile liner trays under a twin-skin roof. If in doubt, assume fragile and plan as if it will give way.
When you are writing the job pack, the Roofing RAMS Template UK shows a typical structure for sequence, access and fragile roof controls.
The pre-quote survey that finds the fragility
I never price a job on a fragile roof without a look from below. Walk the building with the client. Check purlin spacing, see if any sheets sag between supports, look for daylight at end laps, cracked GRP, soft timber and temporary patches. If there is a ceiling, find an access hatch or take a tile out to inspect. A 10 minute look under the roof can save a funeral speech.
Ask blunt questions. How old is the roof, has it been oversheeted, where are the rooflights and how many, any known leaks or previous footfalls, what are the sheet types, and how is access planned right now. Ask what is under the work area, can you net it, or can you set up a crash deck or mobile platform. Find out the live operations below, like forklifts or production lines, that would stop you netting or staging from underneath.
Measure things that matter. Purlin centres, bay sizes, distance from eaves to first purlin, opening sizes for rooflights and vents. Check fixings for corrosion and pull-out risk. Photograph each elevation, every rooflight, and any areas you think are suspect. Mark up a plan so you can show the client which bays need covers and staging. If you cannot get to the underside, say so in the quote and include a provisional survey visit before work starts.
If you are tightening up your sequence and access plan, this roof work method statement article covers how to set it out clearly.
Controls on the roof: covers, staging and safe systems
On a fragile roof, you plan where feet can and cannot go. That starts with a designated access route and working platforms that spread the load to the purlins. Use properly supported staging, crawling boards or proprietary roof walkways. Secure them so they cannot skate on a wet sheet. In RAMS I want to see how you will support boards on the structure below, not just lay timber and hope.
Every rooflight and opening gets a cover that will take a person’s weight with margin, or a full barrier around it. Make the covers bright and fixed, not a loose board you plan to move as you go. HSG33 is clear, protect rooflights and fragile areas before starting work nearby. Slap a warning sign on each one. If you need to uncover it for the task, re-guard it immediately after.
Set out a no-step zone between purlins where the sheet spans are longest and weakest, then a go-zone only on staging, boards or platforms. Mark the route with flags or paint. Keep materials on the staging, not on the sheets. A part-loaded sheet can look fine, then drop when someone adds a bit more weight to reach over. That is the classic moment a hand goes through and the rest follows.
Edge protection still matters because people make mistakes, but do not kid yourself it is the main control here. It will not stop you going through a brittle GRP light. If you need a short tether for certain tasks, fine, but HSG33 and the Work at Height Regulations put collective measures first. So plan covers, staging and nets before you reach for a harness.
Nets, soft landings and working from below
Safety nets save lives when the sheet gives way. If there is a clear drop below and suitable structure to fix to, plan nets under the work area. They need to be installed by competent riggers, clipped to sound steel or timber, and inspected. HSG33 explains where nets and soft landing systems fit in, and the Work at Height Regulations require you to mitigate the consequences of a fall if you cannot eliminate the risk.
Sometimes you cannot net, for example on a busy warehouse with racking to the rafters, or a food plant with hygiene controls. Then you may be into crash decks, birdcage scaffolds or working from MEWPs below while operating through openings. All of that needs planning, isolation below, and a tidy exclusion zone so no one walks under you or stacks a pallet where a net should be.
If you can remove the need to be on the fragile surface by working from below, do it. Replace rooflights from a MEWP through an opening, fix bolts from under a liner tray, or oversheet from a staged platform as you progress. HSG33 pushes that hierarchy. The Work at Height Regulations say avoid the risk where you can, prevent a fall where you cannot, and mitigate if a fall still happens.
Barriers, signage, supervision and finishing safely
I want to see barriers and signs as soon as you step off the ladder. Fragile roof areas and rooflights should have prominent warnings. Use clear wording like DANGER FRAGILE ROOF. Keep a controlled access point with a briefing board, harness anchor points where needed, and a supervisor who says no when the plan slips. HSG33 and the Work at Height Regulations expect visible warnings and managed access around fragile surfaces.
Weather and housekeeping make or break the job. Wet fibre cement is like ice. Do not work on it in rain or frost. Sweep moss and debris before you start, and keep the staging clean. I have watched people turn a safe set-up into a slide by leaving offcuts and sealant tubes underfoot. Tool lanyards and debris nets below keep those on the ground safe too.
Have a rescue plan that works for a person who has gone through to a net, or is hanging off staging. Practice it once, not in anger on the day. If you need a permit to work at height on that site, build the fragile roof controls into it so the gatekeeper checks them. The paperwork is not the job, but on fragile roofs it forces you to be specific, which is good discipline.
Questions we get asked
What is classed as a fragile roof in the UK?
Any surface that will not safely take the weight of a person or load is classed as fragile, including fibre cement sheets, old GRP or PVC rooflights, corroded metal sheets and rotten timber. HSG33 Health and safety in roof work gives the practical guidance, and the Work at Height Regulations 2005 set the legal duties.
How do you make a fragile roof safe to work on?
Plan access routes and use staging or crawling boards supported on the structure, cover or guard all rooflights and openings, and install safety nets or crash decks where possible. Add barriers and prominent signage. These are the measures described in HSG33 and required by the Work at Height Regulations when the risk cannot be avoided.
Do I need signs for fragile roof areas?
Yes. Where there is a risk of a fall through a fragile surface that you cannot avoid, the Work at Height Regulations 2005 require prominent warning signs. In practice that means clear wording like DANGER FRAGILE ROOF at access points and around rooflights or fragile zones, as reinforced by HSG33 guidance.
Are rooflights always treated as fragile?
Treat rooflights as fragile unless you have clear evidence they are non-fragile and protected. Age, UV exposure and coatings make many GRP or PVC lights brittle. HSG33 is explicit on guarding or covering rooflights before work starts nearby, and many fatalities involve falls through unprotected lights.
When should safety nets be used under a fragile roof?
Use nets where there is sufficient height and structure to fix them, and where they will protect anyone working above if a sheet fails. HSG33 places nets and soft landing systems as a key collective protection measure, and any netting must be installed and inspected by competent people in line with current industry practice.
The short version
Fragile roofs kill by letting people fall through, not over the edge. Fibre cement, old rooflights and corroded metal should be treated as fragile until proven otherwise.
Survey from below, plan staging and covers, protect every rooflight, and use nets or crash decks where you can. Back it with barriers, clear signage and a real rescue plan. HSG33 and the Work at Height Regulations 2005 set the standard, and HSE’s fatal injury statistics show why this matters.
If you need this written up properly for a real job, the paperwork is the easy part now.
Build your roofing RAMS with RAMS AIWritten by the RAMS AI team at United Applications Ltd. Our content is informed by over 30 years of construction industry experience and reviewed for alignment with current UK health and safety legislation including the CDM 2015 Regulations and HSE guidance.